site-ffpb/site.conf

{
	-- A new node's name will be autogenerated from
	-- it's primary MAC address and this prefix.
	-- e.g. freifunk-0123456789ab
	hostname_prefix = 'freifunk',

	-- name of this community
	site_name = 'Freifunk Paderborn',
	-- short name of this community
	site_code = 'ffpb',

	-- v4 and v6 prefixes in which nodes+clients might get an IP
	prefix4 = '10.132.0.0/16',
	prefix6 = 'fdca:ffee:ff12:132::/64',

	-- timezone
	timezone = 'CET-1CEST,M3.5.0,M10.5.0/3', -- Europe/Berlin

	-- network-internal ntp service
	ntp_servers = {'ntp.services.ffpb'},

	-- regulatory domain of your wifi
	regdom = 'DE',

	-- wifi settings (2.4 GHz and 5 GHz)
	-- the most important thing to change is the SSID
	-- of the client network (yourcity.freifunk.net) and
	-- both(!) mesh_?ssid ad-hoc mesh network ids.
	wifi24 = {
		ssid = 'paderborn.freifunk.net',
		channel = 1,
		htmode = 'HT40+',
		mesh_ssid = '02:d1:11:13:87:ad',
		mesh_bssid = '02:d1:11:13:87:ad',
		mesh_mcast_rate = 12000,
	},
	wifi5 = {
		ssid = 'paderborn.freifunk.net (5GHz)',
		channel = 44,
		htmode = 'HT40+',
		mesh_ssid = '02:d1:11:13:87:ad',
		mesh_bssid = '02:d1:11:13:87:ad',
		mesh_mcast_rate = 12000,
	},

	-- IP address of each router
	-- At this IP a client can always connect to its
	-- currently connected node. Both v4 and v6 addr.
	-- must lie in the above prefix4 and prefix6.
	next_node = {
		ip4 = '10.132.0.1',
		ip6 = 'fdca:ffee:ff12:132::1',

		-- mac address, must be unique in the client network
		-- (usually, you don't need to change this)
		mac = '16:41:95:40:f7:dc',
	},

	-- fastd (vpn) settings
	fastd_mesh_vpn = {
		-- cipher(s) to use
		methods = {'salsa2012+gmac'},

		-- the maximum transfer unit
		-- use 1426 for IPv4 gateways
		mtu = 1426,

		backbone = {
			-- specifies how many servers are contacted
			-- by a client simultanously
			limit = 2,

			-- list all available vpn servers
			peers = {
				gw01 = {
					-- public fastd key of the vpn server
					key = '97bc56ae561f67cfe15364134868c3553b5f1eab06f7bd9c5b93fbf280a52b51',
					-- remotes is an array of ways on how to reach the VPN server
					-- Use public addresses here, these addresses are used when the mesh might not be connected yet.
					-- format: '[|ipv4|ipv6] "hostname-or-ip-address" port 10000'
					remotes = {'ipv6 "v6.gw01.paderborn.freifunk.net" port 10000', 'ipv4 "v4.gw01.paderborn.freifunk.net" port 10000'},
				},
				gw02 = {
					key = 'e8fa9bf402fd33dd1ba804a97f2e46c704423ff49e9c55312845a7bfb93121ad',
					remotes = {'ipv6 "v6.gw02.paderborn.freifunk.net" port 10000', 'ipv4 "v4.gw02.paderborn.freifunk.net" port 10000'},
				},
				gw03 = {
					key = 'cf7b54f7221a26251a5970e1d404f864ff4bfed3254bd741cf754445e040b9d0',
					remotes = {'ipv6 "v6.gw03.paderborn.freifunk.net" port 10000', 'ipv4 "v4.gw03.paderborn.freifunk.net" port 10000'},
				},
				gw04 = {
					key = 'cf3855e5fa04e4c04a294cb6e8902f91c7ff7ef82bf031cc842a2b79b936677c',
					remotes = {'ipv6 "v6.gw04.paderborn.freifunk.net" port 10000', 'ipv4 "v4.gw04.paderborn.freifunk.net" port 10000'},
				},
			},
		},
	},

	-- configure the autoupdater
	autoupdater = {
		enabled = 1,

		-- default branch for a firmware
		-- In config-mode, the user can select a different branch from below
		branch = 'stable',

		-- available branches for the autoupdater
		branches = {
			stable = {
				-- visible name of this branch (why not use the internal identifier here, too)
				name = 'stable',

				-- where to get the manifest file (without the trailing /manifest)
				-- It's wise to use an internal address here,
				-- but specifying a publicly available update site does not hurt.
				mirrors = {'http://[fdca:ffee:ff12:a254::80]/stable', 'http://firmware.paderborn.freifunk.net/stable'},
				-- A node rolls the dice once per hour - with
				-- this probably the dice says "go check if there is new firmware"
				-- A value of 8% (0.08) means that we estimate a update check every 12-13 hours (100/8=12.5).
				probability = 0.08,

				-- Number of valid manifest signatures necessary to accept the manifest as "good".
				good_signatures = 2,

				-- list of public keys which are considered "good" for manifest signatures
				pubkeys = {
					'16b0e942929d6592d4a01b66b334427ba4db03b388a876432958d9010bd8d8b5', -- HeJ
					'b0197042824a752c2dba717a4b2ded88852111bbe12e6b5f57fdfa3abb9312c0', -- thardes2
					'ba2e6ff4de41ade9959702195d4c26c764e7aab85c627363681c29dbc4a8a2c5', -- oscar-
				},
			},
			testing = {
				name = 'testing',
				mirrors = {'http://[fdca:ffee:ff12:a254::80]/testing','http://firmware.paderborn.freifunk.net/testing'},
				probability = 0.25,
				good_signatures = 1,
				pubkeys = {
					'16b0e942929d6592d4a01b66b334427ba4db03b388a876432958d9010bd8d8b5', -- HeJ
					'b0197042824a752c2dba717a4b2ded88852111bbe12e6b5f57fdfa3abb9312c0', -- thardes2
					'ba2e6ff4de41ade9959702195d4c26c764e7aab85c627363681c29dbc4a8a2c5', -- oscar-
				},
			},
		},
	},

	-- default traffic shaping (bandwidth limit) settings
	simple_tc = {
		mesh_vpn = {
			ifname = 'mesh-vpn',
			enabled = 0,
			limit_egress = 200,
			limit_ingress = 3000,
		},
	},

	-- configure ffpb-debug
	debugserver = {
		host = 'debugreport.paderborn.freifunk.net',
		port = 1337,
		liveport = 1338,
	},

	-- enable BATMAN on WAN interface by default (requires gluon-batman-on-wan package)
	batman_on_wan = 0,

	-- custom messages in config mode
	config_mode = {
		msg_welcome = [[
Willkommen zum Einrichtungsassistenten für deinen neuen Paderborner
Freifunk-Knoten. Fülle das folgende Formular deinen Vorstellungen
entsprechend aus und sende es ab.
]],
		msg_pubkey = [[
Dies ist der öffentliche Schlüssel deines Freifunkknotens. Erst nachdem
er auf den Servern des Paderborner Freifunk-Projektes eingetragen wurde,
kann sich dein Knoten mit dem Paderborner Mesh-VPN zu verbinden. Bitte
schicke uns dazu diesen Schlüssel und den Namen deines Knotens
an maschinenraum@paderborn.freifunk.net oder benutze am besten gleich das
<a href="http://paderborn.freifunk.net/?page_id=366&key=<%=pubkey%>&nname=<%=hostname%>&mac=<%=sysconfig.primary_mac%>">
vorausgefüllte Formular auf unserer Webseite</a>.
]],
		msg_reboot = [[
<p>
Dein Knoten startet gerade neu und wird anschließend versuchen,
sich anschließend mit anderen Freifunkknoten in seiner Nähe zu
verbinden. Weitere Informationen zur
Paderborner Freifunk-Community findest du auf
<a href="http://paderborn.freifunk.net/">unserer Webseite</a>.
</p>
<p>
Viel Spaß mit deinem Knoten und der Erkundung von Freifunk!
</p>
]],
	},
}