|
|
@@ -0,0 +1,413 @@
|
|
|
+From: Sven Roederer <devel-sven@geroedel.de>
|
|
|
+Date: Mon, 29 May 2017 11:24:49 +0200
|
|
|
+Subject: ramips: add support for Ubiquiti EdgeRouter X-SFP
|
|
|
+
|
|
|
+This patch adds support for the Ubiquiti EdgeRouter X-SFP and
|
|
|
+improves support for the EdgeRouter X (PoE-passthrough).
|
|
|
+
|
|
|
+Specification:
|
|
|
+- SoC: MediaTek MT7621AT
|
|
|
+- Flash: 256 MiB
|
|
|
+- RAM: 265 MiB
|
|
|
+- Ethernet: 5 x LAN (1000 Mbps)
|
|
|
+- UART: 1 x UART on PCB (3.3V, RX, TX, GND) - 57600 8N1
|
|
|
+- EdgeRouter X:
|
|
|
+ - 1 x PoE-Passtrough (Eth4)
|
|
|
+ - powered by Wallwart or passive PoE
|
|
|
+- EdgeRouter X-SFP:
|
|
|
+ - 5 x PoE-Out (24V, passive)
|
|
|
+ - 1 x SFP (unknown status)
|
|
|
+ - powered by Wallwart (24V)
|
|
|
+
|
|
|
+Doesn't work:
|
|
|
+* SoC has crypto engine but no open driver.
|
|
|
+* SoC has nat acceleration, but no open driver.
|
|
|
+* This router has 2MB spi flash soldered in but MT
|
|
|
+ nand/spi drivers do not support pin sharing,
|
|
|
+ so it is not accessable and disabled. Stock
|
|
|
+ firmware could read it and it was empty.
|
|
|
+
|
|
|
+Installation
|
|
|
+
|
|
|
+via vendor firmware:
|
|
|
+- build an Initrd-image (> 3MiB) and upload the factory-image
|
|
|
+- initrd can have luci-mod-failsafe
|
|
|
+- flash final firmware via LuCI / sysupgrade on rebooted system
|
|
|
+
|
|
|
+via TFTP:
|
|
|
+- stop uboot into tftp-load into option "1"
|
|
|
+- upload factory.bin image
|
|
|
+
|
|
|
+Signed-off-by: Sven Roederer <devel-sven@geroedel.de>
|
|
|
+
|
|
|
+diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
|
|
|
+index 1778dc93297136e3196ad3f74e4b3bea7535cee0..1f5c6429201ba05fc14ff09c6c562d2c114f2a63 100755
|
|
|
+--- a/target/linux/ramips/base-files/etc/board.d/02_network
|
|
|
++++ b/target/linux/ramips/base-files/etc/board.d/02_network
|
|
|
+@@ -146,6 +146,7 @@ ramips_setup_interfaces()
|
|
|
+ rb750gr3|\
|
|
|
+ rt-n14u|\
|
|
|
+ ubnt-erx|\
|
|
|
++ ubnt-erx-sfp|\
|
|
|
+ ur-326n4g|\
|
|
|
+ wrtnode|\
|
|
|
+ wrtnode2p | \
|
|
|
+diff --git a/target/linux/ramips/base-files/etc/board.d/03_gpio_switches b/target/linux/ramips/base-files/etc/board.d/03_gpio_switches
|
|
|
+new file mode 100755
|
|
|
+index 0000000000000000000000000000000000000000..859dfb31f51244e69d3dce5fc80b329cb57729f3
|
|
|
+--- /dev/null
|
|
|
++++ b/target/linux/ramips/base-files/etc/board.d/03_gpio_switches
|
|
|
+@@ -0,0 +1,25 @@
|
|
|
++#!/bin/sh
|
|
|
++
|
|
|
++. /lib/functions/uci-defaults.sh
|
|
|
++. /lib/ramips.sh
|
|
|
++
|
|
|
++board_config_update
|
|
|
++
|
|
|
++board=$(ramips_board_name)
|
|
|
++
|
|
|
++case "$board" in
|
|
|
++ubnt-erx)
|
|
|
++ ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "0"
|
|
|
++ ;;
|
|
|
++ubnt-erx-sfp)
|
|
|
++ ucidef_add_gpio_switch "poe_power_port0" "PoE Power Port0" "496"
|
|
|
++ ucidef_add_gpio_switch "poe_power_port1" "PoE Power Port1" "497"
|
|
|
++ ucidef_add_gpio_switch "poe_power_port2" "PoE Power Port2" "498"
|
|
|
++ ucidef_add_gpio_switch "poe_power_port3" "PoE Power Port3" "499"
|
|
|
++ ucidef_add_gpio_switch "poe_power_port4" "PoE Power Port4" "500"
|
|
|
++ ;;
|
|
|
++esac
|
|
|
++
|
|
|
++board_config_flush
|
|
|
++
|
|
|
++exit 0
|
|
|
+diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh
|
|
|
+index 17ada648931f16d3e85630dd341defb89ba50d6f..b1091f66b2897a19bd01d4a26a1b3647656fa62b 100755
|
|
|
+--- a/target/linux/ramips/base-files/lib/ramips.sh
|
|
|
++++ b/target/linux/ramips/base-files/lib/ramips.sh
|
|
|
+@@ -466,6 +466,9 @@ ramips_board_detect() {
|
|
|
+ *"UBNT-ERX")
|
|
|
+ name="ubnt-erx"
|
|
|
+ ;;
|
|
|
++ *"UBNT-ERX-SFP")
|
|
|
++ name="ubnt-erx-sfp"
|
|
|
++ ;;
|
|
|
+ *"UR-326N4G")
|
|
|
+ name="ur-326n4g"
|
|
|
+ ;;
|
|
|
+diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh
|
|
|
+index a5cca2080d3b96cef92286b1b15f4f8832d9f8c5..d3efc2dd37ed855a1c0e966e448b67ae73324d5f 100755
|
|
|
+--- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
|
|
|
++++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
|
|
|
+@@ -234,7 +234,8 @@ platform_check_image() {
|
|
|
+ }
|
|
|
+ return 0
|
|
|
+ ;;
|
|
|
+- ubnt-erx)
|
|
|
++ ubnt-erx|\
|
|
|
++ ubnt-erx-sfp)
|
|
|
+ nand_do_platform_check "$board" "$1"
|
|
|
+ return $?;
|
|
|
+ ;;
|
|
|
+@@ -248,7 +249,8 @@ platform_nand_pre_upgrade() {
|
|
|
+ local board=$(ramips_board_name)
|
|
|
+
|
|
|
+ case "$board" in
|
|
|
+- ubnt-erx)
|
|
|
++ ubnt-erx|\
|
|
|
++ ubnt-erx-sfp)
|
|
|
+ platform_upgrade_ubnt_erx "$ARGV"
|
|
|
+ ;;
|
|
|
+ esac
|
|
|
+@@ -258,7 +260,8 @@ platform_do_upgrade() {
|
|
|
+ local board=$(ramips_board_name)
|
|
|
+
|
|
|
+ case "$board" in
|
|
|
+- ubnt-erx)
|
|
|
++ ubnt-erx|\
|
|
|
++ ubnt-erx-sfp)
|
|
|
+ nand_do_upgrade "$ARGV"
|
|
|
+ ;;
|
|
|
+ *)
|
|
|
+diff --git a/target/linux/ramips/dts/UBNT-ER-e50.dtsi b/target/linux/ramips/dts/UBNT-ER-e50.dtsi
|
|
|
+new file mode 100644
|
|
|
+index 0000000000000000000000000000000000000000..b38c7194942db9f0a713fd8f707b53820d07c78e
|
|
|
+--- /dev/null
|
|
|
++++ b/target/linux/ramips/dts/UBNT-ER-e50.dtsi
|
|
|
+@@ -0,0 +1,106 @@
|
|
|
++#include "mt7621.dtsi"
|
|
|
++
|
|
|
++#include <dt-bindings/gpio/gpio.h>
|
|
|
++#include <dt-bindings/input/input.h>
|
|
|
++
|
|
|
++/ {
|
|
|
++ compatible = "ubiquiti,edgerouterx";
|
|
|
++
|
|
|
++ memory@0 {
|
|
|
++ device_type = "memory";
|
|
|
++ reg = <0x0 0x10000000>;
|
|
|
++ };
|
|
|
++
|
|
|
++ chosen {
|
|
|
++ bootargs = "console=ttyS0,57600";
|
|
|
++ };
|
|
|
++
|
|
|
++ gpio-keys-polled {
|
|
|
++ compatible = "gpio-keys-polled";
|
|
|
++ #address-cells = <1>;
|
|
|
++ #size-cells = <0>;
|
|
|
++ poll-interval = <20>;
|
|
|
++
|
|
|
++ reset {
|
|
|
++ label = "reset";
|
|
|
++ gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
|
|
++ linux,code = <KEY_RESTART>;
|
|
|
++ };
|
|
|
++ };
|
|
|
++};
|
|
|
++
|
|
|
++ðernet {
|
|
|
++ mtd-mac-address = <&factory 0x22>;
|
|
|
++};
|
|
|
++
|
|
|
++&nand {
|
|
|
++ status = "okay";
|
|
|
++
|
|
|
++ partition@0 {
|
|
|
++ label = "u-boot";
|
|
|
++ reg = <0x0 0x80000>;
|
|
|
++ read-only;
|
|
|
++ };
|
|
|
++
|
|
|
++ partition@80000 {
|
|
|
++ label = "u-boot-env";
|
|
|
++ reg = <0x80000 0x60000>;
|
|
|
++ read-only;
|
|
|
++ };
|
|
|
++
|
|
|
++ factory: partition@e0000 {
|
|
|
++ label = "factory";
|
|
|
++ reg = <0xe0000 0x60000>;
|
|
|
++ };
|
|
|
++
|
|
|
++ partition@140000 {
|
|
|
++ label = "kernel1";
|
|
|
++ reg = <0x140000 0x300000>;
|
|
|
++ };
|
|
|
++
|
|
|
++ partition@440000 {
|
|
|
++ label = "kernel2";
|
|
|
++ reg = <0x440000 0x300000>;
|
|
|
++ };
|
|
|
++
|
|
|
++ partition@740000 {
|
|
|
++ label = "ubi";
|
|
|
++ reg = <0x740000 0xf7c0000>;
|
|
|
++ };
|
|
|
++};
|
|
|
++
|
|
|
++&pinctrl {
|
|
|
++ state_default: pinctrl0 {
|
|
|
++ gpio {
|
|
|
++ ralink,group = "uart2", "uart3", "i2c", "pcie", "rgmii2", "jtag";
|
|
|
++ ralink,function = "gpio";
|
|
|
++ };
|
|
|
++ };
|
|
|
++};
|
|
|
++
|
|
|
++&spi0 {
|
|
|
++ /* This board has 2Mb spi flash soldered in and visible
|
|
|
++ from manufacturer's firmware.
|
|
|
++ But this SoC shares spi and nand pins,
|
|
|
++ and current driver does't handle this sharing well */
|
|
|
++ status = "disabled";
|
|
|
++
|
|
|
++ m25p80@0 {
|
|
|
++ #address-cells = <1>;
|
|
|
++ #size-cells = <1>;
|
|
|
++ compatible = "jedec,spi-nor";
|
|
|
++ reg = <1>;
|
|
|
++ spi-max-frequency = <10000000>;
|
|
|
++ m25p,chunked-io = <32>;
|
|
|
++
|
|
|
++ partition@0 {
|
|
|
++ label = "spi";
|
|
|
++ reg = <0x0 0x200000>;
|
|
|
++ read-only;
|
|
|
++ };
|
|
|
++ };
|
|
|
++};
|
|
|
++
|
|
|
++&xhci {
|
|
|
++ status = "disabled";
|
|
|
++};
|
|
|
+diff --git a/target/linux/ramips/dts/UBNT-ERX-SFP.dts b/target/linux/ramips/dts/UBNT-ERX-SFP.dts
|
|
|
+new file mode 100644
|
|
|
+index 0000000000000000000000000000000000000000..ca26d817211e5a5a20a7da926cd2aee726875780
|
|
|
+--- /dev/null
|
|
|
++++ b/target/linux/ramips/dts/UBNT-ERX-SFP.dts
|
|
|
+@@ -0,0 +1,24 @@
|
|
|
++/dts-v1/;
|
|
|
++
|
|
|
++#include "UBNT-ER-e50.dtsi"
|
|
|
++
|
|
|
++#include <dt-bindings/gpio/gpio.h>
|
|
|
++
|
|
|
++/ {
|
|
|
++ model = "UBNT-ERX-SFP";
|
|
|
++ compatible = "ubiquiti,edgerouterx-sfp";
|
|
|
++
|
|
|
++ i2c-gpio {
|
|
|
++ compatible = "i2c-gpio";
|
|
|
++ gpios = <&gpio0 3 GPIO_ACTIVE_HIGH /* sda */
|
|
|
++ &gpio0 4 GPIO_ACTIVE_HIGH /* scl */
|
|
|
++ >;
|
|
|
++ #address-cells = <1>;
|
|
|
++ #size-cells = <0>;
|
|
|
++
|
|
|
++ pca9555@25 {
|
|
|
++ compatible = "pca9555";
|
|
|
++ reg = <0x25>;
|
|
|
++ };
|
|
|
++ };
|
|
|
++};
|
|
|
+diff --git a/target/linux/ramips/dts/UBNT-ERX.dts b/target/linux/ramips/dts/UBNT-ERX.dts
|
|
|
+index cf86bbb7e67b1c521c279367ee9e99fee88fae85..556d1156c352f76a94c6e39bc3b58c88f08815be 100644
|
|
|
+--- a/target/linux/ramips/dts/UBNT-ERX.dts
|
|
|
++++ b/target/linux/ramips/dts/UBNT-ERX.dts
|
|
|
+@@ -1,108 +1,7 @@
|
|
|
+ /dts-v1/;
|
|
|
+
|
|
|
+-#include "mt7621.dtsi"
|
|
|
+-
|
|
|
+-#include <dt-bindings/gpio/gpio.h>
|
|
|
+-#include <dt-bindings/input/input.h>
|
|
|
++#include "UBNT-ER-e50.dtsi"
|
|
|
+
|
|
|
+ / {
|
|
|
+ model = "UBNT-ERX";
|
|
|
+-
|
|
|
+- memory@0 {
|
|
|
+- device_type = "memory";
|
|
|
+- reg = <0x0 0x10000000>;
|
|
|
+- };
|
|
|
+-
|
|
|
+- chosen {
|
|
|
+- bootargs = "console=ttyS0,57600";
|
|
|
+- };
|
|
|
+-
|
|
|
+- gpio-keys-polled {
|
|
|
+- compatible = "gpio-keys-polled";
|
|
|
+- #address-cells = <1>;
|
|
|
+- #size-cells = <0>;
|
|
|
+- poll-interval = <20>;
|
|
|
+-
|
|
|
+- reset {
|
|
|
+- label = "reset";
|
|
|
+- gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;
|
|
|
+- linux,code = <KEY_RESTART>;
|
|
|
+- };
|
|
|
+- };
|
|
|
+-};
|
|
|
+-
|
|
|
+-ðernet {
|
|
|
+- mtd-mac-address = <&factory 0x22>;
|
|
|
+-};
|
|
|
+-
|
|
|
+-&nand {
|
|
|
+- status = "okay";
|
|
|
+-
|
|
|
+- partition@0 {
|
|
|
+- label = "u-boot";
|
|
|
+- reg = <0x0 0x80000>;
|
|
|
+- read-only;
|
|
|
+- };
|
|
|
+-
|
|
|
+- partition@80000 {
|
|
|
+- label = "u-boot-env";
|
|
|
+- reg = <0x80000 0x60000>;
|
|
|
+- read-only;
|
|
|
+- };
|
|
|
+-
|
|
|
+- factory: partition@e0000 {
|
|
|
+- label = "factory";
|
|
|
+- reg = <0xe0000 0x60000>;
|
|
|
+- };
|
|
|
+-
|
|
|
+- partition@140000 {
|
|
|
+- label = "kernel1";
|
|
|
+- reg = <0x140000 0x300000>;
|
|
|
+- };
|
|
|
+-
|
|
|
+- partition@440000 {
|
|
|
+- label = "kernel2";
|
|
|
+- reg = <0x440000 0x300000>;
|
|
|
+- };
|
|
|
+-
|
|
|
+- partition@740000 {
|
|
|
+- label = "ubi";
|
|
|
+- reg = <0x740000 0xf7c0000>;
|
|
|
+- };
|
|
|
+-};
|
|
|
+-
|
|
|
+-&pinctrl {
|
|
|
+- state_default: pinctrl0 {
|
|
|
+- gpio {
|
|
|
+- ralink,group = "uart2", "uart3", "i2c", "pcie", "rgmii2", "jtag";
|
|
|
+- ralink,function = "gpio";
|
|
|
+- };
|
|
|
+- };
|
|
|
+-};
|
|
|
+-
|
|
|
+-&spi0 {
|
|
|
+- /* This board has 2Mb spi flash soldered in and visible
|
|
|
+- from manufacturer's firmware.
|
|
|
+- But this SoC shares spi and nand pins,
|
|
|
+- and current driver does't handle this sharing well */
|
|
|
+- status = "disabled";
|
|
|
+-
|
|
|
+- m25p80@0 {
|
|
|
+- #address-cells = <1>;
|
|
|
+- #size-cells = <1>;
|
|
|
+- compatible = "jedec,spi-nor";
|
|
|
+- reg = <1>;
|
|
|
+- spi-max-frequency = <10000000>;
|
|
|
+- m25p,chunked-io = <32>;
|
|
|
+-
|
|
|
+- partition@0 {
|
|
|
+- label = "spi";
|
|
|
+- reg = <0x0 0x200000>;
|
|
|
+- read-only;
|
|
|
+- };
|
|
|
+- };
|
|
|
+-};
|
|
|
+-
|
|
|
+-&xhci {
|
|
|
+- status = "disabled";
|
|
|
+ };
|
|
|
+diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk
|
|
|
+index 15ea9a13b6310b1454b5b3b92cd8ed30ee6255b3..8218bea84410536151a216cd2cc0300369ad977a 100644
|
|
|
+--- a/target/linux/ramips/image/mt7621.mk
|
|
|
++++ b/target/linux/ramips/image/mt7621.mk
|
|
|
+@@ -144,6 +144,19 @@ define Device/ubnt-erx
|
|
|
+ endef
|
|
|
+ TARGET_DEVICES += ubnt-erx
|
|
|
+
|
|
|
++define Device/ubnt-erx-sfp
|
|
|
++ DTS := UBNT-ERX-SFP
|
|
|
++ FILESYSTEMS := squashfs
|
|
|
++ KERNEL_SIZE := 3145728
|
|
|
++ KERNEL := $(KERNEL_DTB) | uImage lzma
|
|
|
++ IMAGES := sysupgrade.tar
|
|
|
++ KERNEL_INITRAMFS := $$(KERNEL) | ubnt-erx-factory-image $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.tar
|
|
|
++ IMAGE/sysupgrade.tar := sysupgrade-tar | append-metadata
|
|
|
++ DEVICE_TITLE := Ubiquiti EdgeRouter X-SFP
|
|
|
++ DEVICE_PACKAGES := -kmod-mt76 -kmod-rt2x00-lib -kmod-mac80211 -kmod-cfg80211 -wpad-mini -iwinfo kmod-i2c-algo-pca kmod-gpio-pca953x kmod-i2c-gpio-custom
|
|
|
++endef
|
|
|
++TARGET_DEVICES += ubnt-erx-sfp
|
|
|
++
|
|
|
+ define Device/vr500
|
|
|
+ DTS := VR500
|
|
|
+ IMAGE_SIZE := 66453504
|
